- Announce message maximum size has been increased up to 200 characters.
  The new announce.bin file format is NOT compatible with the older
  one :

	* You MUST delete the file dxnet\system\bin\announce.bin used
	  by 3.a16 relase and older;

	* You have to replace the PURGANN utility program wich is also
	  different (into syscmd directory). This is normally done
	  automaticaly if you patched this version.

  Tks SM0RUX.

- Frames lost if Pc/FlexNet buffers was full : fixed.

- Fixed an initialization bug : do not send anything else than init
  protocols during the initialization sequence.

- DxNet sends now the connected node list (PC38) during the link
  initialization sequence. This is for compatibility only.

- Dx spot dupe checking whatever the logger SSID wich is sometimes
  changed/removed by some DxClusters. Tks SM7GVF.

- Announces dupes now checked.

- Just one WWV annoncement allowed per 3 hours.

- Incoming telnet access rejected callsign with SSID. Fixed.

- Fixed outgoing telnet connexion (linux version). Tks SM7GVF.

  Reminder the way to declare a telnet access : SET/PORT +inet:nnnn
  where nnnn is the telnet port number (set to 23 by default).
  The callsigns and password you want to allow to connect are saved into
  system/passwd.dat.

  If you want to use a script file to connect a cluster via telnel port,
  you must use the following syntax :
  .c inet <CALLSIGN> <IP_ADDRESS> [PORT]
  <CALLSIGN>   : the call you want to connect to
  <IP_ADDRESS> : the IP address of the remote telnet host
  [PORT]       : the telnet port, wich is by default set to 23

  I give you as an example the script file I use to connect to SV1AAW :

  --- SV1AAW.FWD ---
  SV1AAW
  .C inet sv1aaw 194.219.59.46 9000
  +clx
  .f5mzn\rmypasswd
  +validated
  ------------------

- Fixed a bad hop count value send to the network after an adjacent hard
  disconnect (on PC21). Tks SM7GVF.

- Logger SSID is not removed from the logger field of a DX protocol even if
  set/dxssid is set to off. This will avoid dupe checking problem on other
  cluster systems. Tks SM7GVF.

- SH/HOPS diplays in two columns. Tks SM0RUX for suggestion.

- Fixed buffer overflow problem (dos version). DxNet should not crash
  anymore if a user want to get a very large bloc of datas wich its size
  is larger than the available memory (e.g. SH/DX/3000). BUT he will receive
  a troncated information if the buffer is full. Tks SM0RUX.

- PURGDX showed negative spot numbers if the number of saved spots was
  larger than 32767. Fixed. Tks G3RTU.

- DxNet now returns a prompt even if it gets a empty command (= just a
  RETURN). This is needed by some script. Tks F1TE.

- If, during a talk, your recipient disconnects, you get a error message
  wich tells that the recipient is no more there. I fixed a bug in this
  message (bad recipient callsign). Tks F1CAY.

- Fixed a bug occuring during the forward (DxNet crashed because it tried to
  close the forward.sys file even if this file doesn't exist). Tks SM7GVF.

- Implemented remote commands protocols (both PC34 and PC35). You must add
  a "tmp" directory in the dxnet one to allow these protocols to be
  managed by DxNet.

- Implemented RCMD/<callsign> <command> sysop function. This command should
  be use to execute commands on remote DxCluster nodes.

- Implemented SH/TNC_status command wich displays each connected
  channels status.

- Implemented SH/C/N command wich displays what nodes are connected locally
  and what nodes are reachable from each og them.

- DISC/CALL <callsign> command moved to DISC <callsign>
  If <callsign> is a cluster, Dxnet sends a PC39 protocol to the adjacent
  wich must be disconnected and informthe other adjacents that the link
  is down.

- PC39 protocol is now supported.

- Implemented INIT <callsign> command, wich request an init sequence to the
  adjacent cluster <callsign> (both PC38 and PC18 protocols).

- 3.0 Release.
